Article Sidebar

Submitted
Jul 26, 2024
Accepted
Sep 8, 2024
Published
Sep 8, 2024
Download
DOWNLOAD PDF
Statistic
Read Counter : 0 Download : 0

Main Article Content

Abstract

The results of an experiment that used an orthogonal Taguchi method to improve shielded metal arc welding (SMAW) were given. The SMAW method was used to join dissimilar metal of SPHC and St. 30. SPHC material has a low carbon steel content, while St. 30C steels contain a medium amount of carbon steel, which is used for tractor shaft axles. Carbon percentages vary slightly between the two substances. This study aimed to achieve the highest possible quality of tensile strength by utilizing the specified SMAW parameters. SPHC material has a low carbon content, whereas St. 30 steel has a moderate carbon content. This study used the Taguchi experimental method with three input variables and three experimental levels. The SNR ratio is used to evaluate the most optimal SMAW performance. ANOVA analysis is used to evaluate the most crucial parameters in determining the response variable. This research has successfully provided input on the combination of SPHC and St. 30C for SMEs. It operates effectively with a welding current of 133 A, a welding voltage of 9 V, and a filler diameter of 2.0 mm. The S/N ratio analysis found that the welding current, voltage, and filler diameter all had a significant impact on the outcome.

Keywords

Taguchi method Tensile strength Dissimilar joint metal Shielded metal arches welding SPHC/St.30

Article Details

How to Cite
Supriyanto, A., Sukarman, S., Mulyadi, D., Djafar Shieddieque, A., Abdulah, A., & Khoirudin, K. (2024). Improving Dissimilar Metal Joining Quality Through Shielded Metal Arc Welding: A Taguchi Optimization Strategy. Jurnal Teknik Mesin Mechanical Xplore, 5(1), 13-23. https://doi.org/10.36805/jtmmx.v5i1.7867

References

  1. [1] B. Anwar, "Analisis Kekuatan Tarik Hasil Pengelasan Tungsten Inert Gas ( Tig ) Kampuh V Ganda Pada Baja Karbon Rendah St 37," Teknologi, vol. 17, no. 3, pp. 33-38, 2018.
  2. [2] J. Lancaster, Handbook of structural welding (Hanbook of structural welding Processes, materials and methods used in the welding pf major structures, pipeline and process plant). England: Abington Publishing, 1997.
  3. [3] D. L. Olson, S. Thomas A, S. Liu, and G. R. Edwards, Welding, brazing, and soldering. ASM International, 1990.
  4. [4] R. Datta, D. Mukerjee, S. Jha, K. Narasimhan, and R. Veeraraghavan, "Weldability characteristics of shielded metal arc welded high strength quenched and tempered plates," Journal of Materials Engineering and Performance, vol. 11, no. 1, pp. 5-10, 2002.
  5. [5] J. P. Oliveira, K. Ponder, E. Brizes, T. Abke, A. J. Ramirez, and P. Edwards, "Combining resistance spot welding and friction element welding for dissimilar joining of aluminum to high strength steels," Journal of Materials Processing Technology, vol. 273, no. January, pp. 116192-116192, 2019.
  6. [6] P. Kah, R. Suoranta, and J. Martikainen, "Advanced gas metal arc welding processes," International Journal of Advanced Manufacturing Technology, vol. 67, no. 1-4, pp. 655-674, 2013.
  7. [7] Boiler & Pressure Vessel Code II Part D Propereties (Matrix) Materials, 978-07918-3235-6, 2010.
  8. [8] K. E. K. Vimal, S. Vinodh, and A. Raja, "Optimization of process parameters of SMAW process using NN-FGRA from the sustainability view point," Journal of Intelligent Manufacturing, vol. 28, no. 6, pp. 1459-1480, 2017.
  9. [9] S. Karuthapandi, M. Ramu, and P. R. Thyla, "Effects of the use of a flat wire electrode in gas metal arc welding and fuzzy logic model for the prediction of weldment shape profile," Journal of Mechanical Science and Technology, vol. 31, no. 5, pp. 2477-2486, 2017.
  10. [10] A. A. M. Aws, "AWSA5.18-A5.18M-2005.pdf," ed, 2005.
  11. [11] A. Abdurahman, S. Sukarman, A. Djafar Shieddieque, S. Safril, D. Setiawan, and N. Rahdiana, "EVALUASI KEKUATAN UJI TARIK PADA PROSES PENGELASAN BUSUR LISTRIK BEDA MATERIAL SPHC DAN S30-C," Jurnal Teknik Mesin Mechanical Xplore, vol. 1, no. 2, pp. 29-37, 2021.
  12. [12] G. E. Linneert, WELDING METALLURGY, 4 ed. American Welding Society, 1994.
  13. [13] Asme, "ASME Boiler and Pressure Vessel Code, Section II Part C - Specifications for Welding Rods, Electrodes, and Filler Metals,"Specification for titanium and titanium-alloy welding electrodes and rods"," ed, 2010, pp. 377-390.
  14. [14] Hot-rolled mild steel plates, sheet and strip, 2010.
  15. [15] ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials, 2013.
  16. [16] S. Sukarman et al., "OPTIMAL TENSILE-SHEAR STRENGTH OF GALVANIZED/MILD STEEL (SPCC-SD) DISSIMILAR RESISTANCE SPOT WELDING USING TAGUCHI DOE," Jurnal Teknologi, vol. 4, pp. 167-177, 2023.
  17. [17] K. Khoirudin, S. Sukarman, N. Rahdiana, and A. Fauzi, "ANALISIS FENOMENA SPRING-BACK / SPRING-GO FACTOR PADA LEMBARAN BAJA KARBON RENDAH MENGGUNAKAN PENDEKATAN EKSPERIMENTAL," Jurnal Teknologi, vol. 14, no. 1, 2022.
  18. [18] F. Mucharom et al., "Tensile shear load in resistance spot welding of dissimilar metals: An optimization study using response surface methodology," Mechanical Engineering for Society and Industry, vol. 3, no. 2, pp. 66-77, 2023.
  19. [19] S. B. Sutono, "Grey-based Taguchi Method to Optimize the Multi-response Design of Product Form Design," Jurnal Optimasi Sistem Industri, vol. 20, no. 2, pp. 136-146, 2021.
  20. [20] S. Sukarman, A. Abdulah, A. D. Shieddieque, N. Rahdiana, and K. Khoirudin, "OPTIMIZATION OF THE RESISTANCE SPOT WELDING PROCESS OF SECC-AF AND SGCC GALVANIZED STEEL SHEET USING THE TAGUCHI METHOD," SINERGI, vol. 25, no. 3, pp. 319-328, 2021.
  21. [21] S. Shafee, B. B. Naik, and K. Sammaiah, "Resistance Spot Weld Quality Characteristics Improvement By Taguchi Method," Materials Today: Proceedings, vol. 2, no. 4-5, pp. 2595-2604, 2015.
  22. [22] A. Abdulah, S. Sukarman, C. Anwar, A. Djafar Shieddieque, and A. Ilmar Ramadhan, "Optimization of yarn texturing process DTY-150D/96F using taguchi method," Technology Report of Kansai University, vol. 62, no. 4, pp. 1471-1479, 2020.
  23. [23] A. G. Thakur and V. M. Nandedkar, "Optimization of the Resistance Spot Welding Process of Galvanized Steel Sheet Using the Taguchi Method," Arabian Journal for Science and Engineering, vol. 39, no. 2, pp. 1171-1176, 2014.
  24. [24] P. Muthu, "Optimization of the Process Parameters of Resistance Spot Welding of AISI 316l Sheets Using Taguchi Method," Mechanics and Mechanical Engineering, vol. 23, no. 1, pp. 64-69, 2019.
  25. [25] P. G. Mathews, Design of Experiments with MINITAB, 12 ed. Milwaukee: Mathews, Paul G., 2005, pp. 205-205.
  26. [26] S. Chandramouli and K. Eswaraiah, "Optimization of EDM Process parameters in Machining of 17-4 PH Steel using Taguchi Method," Materials Today: Proceedings, vol. 4, no. 2, pp. 2040-2047, 2017.
  27. [27] O. O. Agboola et al., "Optimization of heat treatment parameters of medium carbon steel quenched in different media using Taguchi method and grey relational analysis," Heliyon, vol. 6, no. 7, p. e04444, Jul 2020.
  28. [28] R. Ramadass, S. Sambasivam, and K. Thangavelu, "Selection of optimal parameters in V-bending of Ti-Grade 2 sheet to minimize springback," Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 41, no. 1, pp. 1-11, 2019.
  29. [29] N. Tamilselvan, M. Thirumarimurugan, and E. Sudalai Manikandan, "Study on various control strategies of plate type heat exchanger for non-Newtonian fluids," Journal of Ambient Intelligence and Humanized Computing, vol. 12, no. 7, pp. 7253-7261, 2021.
  30. [30] A. G. Thakur, T. E. Rao, M. S. Mukhedkar, and V. M. Nanedkar, "Application of Taguchi Method for Resistance Spot Welding of Galvanized Steel," vol. 5, no. 11, 2010.
  31. [31] A. D. Shieddieque, S. Sukarman, M. Mardiyati, B. Widyanto, and Y. Aminanda, "Multi-objective Optimization of Sansevieria Trifasciata Fibre Reinforced Vinyl Ester (STF/VE) Bio-composites for the Sustainable Automotive Industry," Automotive Experiences, vol. 5, no. 3, pp. 288-303, 2022.
  32. [32] A. Budianto, S. Sukarman, S. B. Jumawan, and A. Abdulah, "OPTIMASI RESPON TUNGGAL PADA PROSES TEXTURING BENANG DTY-150D / 96F MENGGUNAKAN METODE TAGUCHI SINGLE RESPONSE OPTIMIZATION OF DTY-150D / 96F YARN TEXTURING PROCESS USING TAGUCHI METHOD," Arena Tekstil, vol. 35, no. 2, pp. 77-86, 2020.
  33. [33] A. Badrish, A. Morchhale, N. Kotkunde, and S. K. Singh, "Parameter Optimization in the Thermo-mechanical V-Bending Process to Minimize Springback of Inconel 625 Alloy," Arabian Journal for Science and Engineering, vol. 45, no. 7, pp. 5295-5309, 2020.
  34. [34] S. Sukarman, A. D. Shieddieque, C. Anwar, N. Rahdiana, and A. I. Ramadhan, "Optimization of Powder Coating Process Parameters in Mild Steel (Spcc-Sd) To Improve Dry Film Thickness," Journal of Applied Engineering Science, vol. 19, no. 2, pp. 1-9, 2021.
  35. [35] Minitab. (2023, 10/12/2023). Overview for Probability Plot.
  36. [36] A. Abdelkefi, M. R. Hajj, and A. H. Nayfeh, "Power harvesting from transverse galloping of square cylinder," Nonlinear Dynamics, vol. 70, no. 2, pp. 1355-1363, 2012.