Usulan Desain Troli Barang Menggunakan Pendekatan Antropometri Dan Ergonomi Partisipatori (Studi Kasus PT. Mataram Tunggal Garment)

  • Mukhamad Nur Iskandar Universitas Islam Indonesia
  • Dian Janari Universitas Islam Indonesia
Keywords: Goods Trolley Design, Anthropometry, Participatory Ergonomics

Abstract

Material handling is very important in the production process. PT. Mataram Tunggal Garment uses a goods trolley as a tool to mobilize cardboard boxes containing products. In practice, many employees experience complaints such as back pain due to manually raising and lowering product, difficulty passing downhill and incline due to the absence of brakes, the trolley is difficult to operate, and the trolley is too heavy. If this problem is not resolved immediately, it will have a negative impact on employee safety and company productivity. Therefore, this study aims to design recommendations for goods trolley in the finishing and packing division. From the results, the percentile used for shoulder width is P95: 53 cm, standing elbow height is P5: 84.5 cm and forward hand reach is P5: 65 cm. The proposed design is to add brakes to make it easier to go through inclines or descents, the handle of the trolley can be adjusted in height, the trolley is designed to raise and lower cartons automatically, the size of the trolley container is made to be adjusted to the size of the carton, adding wheel locks, and choosing the stainless steel and polypropylene plastic as a material because of their strength and lightness.

References

Darna, N. (2018). MEMILIH METODE PENELITIAN YANG TEPAT:. Ekonologi.

Gumilar, R., Haryo, Prawahandaru, Muqaffi, & Sayid, M. (2020). TEG WATCH (THE GUIDER WATCH) Inovasi Jam Tangan Pencegah Tindak Kejahatan Bagi Penderita Tuna Wicara. Khazanah: Jurnal Mahasiswa.

Hertanto. (2017). PERANCANGAN PERBAIKAN PADA KURSI KERJA BERDASAR ASPEK ANTROPOMETRI DI CV. MITRA JAYA. Doctoral dissertation, University of Muhammadiyah Malang.

Indriati, E. (2010). Antropometri Untuk Kedokteran, Keperawatan, Gizi, dan Olahraga. Yogyakarta: Citra Aji Parama.

Masâ, E., Fatmawati, W., & Ajibta, L. (2021). Analisa Manual Material Handling (MMH) dengan Menggunakan Metode Biomekanika untuk Mengidentifikasi Resiko Cidera Tulang Belakang (Musculoskeletal Disorder) (Studi Kasus pada Buruh Pengangkat Beras di Pasar Jebor Demak).
Majalah Ilmiyah Sultan Agung.

Niebel, B., & Freivalds, A. (2002). Methods, Standards and Work Design 11th ed. Recherche. Pheasant, S. (1988). Bodysoace : Antropometry, Ergonomics and the Design of Work. London: Taylor & Francis Ltd.

Purnomo, H. (2012). Perancangan Sistem Kerja Berkelanjutan: Pendekatan Holistik Untuk Meningkatkan. Yogyakarta.

Purnomo, H. (2013). Antropometri dan Aplikasinya. Yogyakarta: Graha Ilmu.

Ramadhan, R. N., Sujana, I., & Rahmahwati. (2020). R. RANCANG BANGUN ALAT PENGUPAS METE MENGGUNAKAN PERTIMBANGAN ANTROPOMETRI DAN RAPID UPPER LIMB ASSESSMENT (RULA). urnal TIN Universitas Tanjungpura.

Santoso, A., Anna, B., & Purbasari, A. (2016). Perancangan Ulang Kursi Antropometri Untuk Memenuhi Standar Pengukuran. Profisiensi.

Setiabudi, M. A. (2016). PERANCANGAN ULANG TATA LETAK FASILITAS PABRIK GUNA MEMINIMALKAN JARAK PERPINDAHAN BAHAN DAN BIAYA MATERIAL HANDLING DI PT. JINDAL STAINLESS STEEL INDONESIA STAINLESS STEEL INDONESIA. Doctoral dissertation, Universitas Muhammadiyah Gresik.

Wickens, C. D. (2004). An Introduction to Human Factors Engineering 2nd Edition. Pearson Education Inc.

Wilson, J. R., & Haines, H. M. (1998). Development of a Framework for Participatory Ergonomic. UK: HSE BOOKs.

Zulfikar, I. (2017). Tingkat Pengetahuan Karyawan Terhadap Penggunaan Mouse Dan Keyboard Secara Ergonomis Di Pt. Expro Indonesia Balikpap An. Identifikasi. Jurnal Ilmiah Keselamatan, Kesehatan Kerja dan Lindungan Lingkungan 3.
Published
2021-09-15